Viking C-1000B Especificações descarregar pdf (Página 7)

D. Security Code

DIP Switches shown

in the factory default

positions

DOOR ENTRY / CCTV VIDEO

/ PAGING CONTROLLER

VIKING

MODEL C-1000B

PWR 13.8

DOOR

STRIKE 1

DOOR

STRIKE 2

DOORBOX 2

DOORBOX

PWR OUTPU

DOORBOX 1

123456789

10 11 12 13

14 15 16 17 18 19

EARTH

GND

PHONE LINE

INPUT

LINE OUT

TO PHONES

KEYLESS CONTACT

CLOSURE INPUT

VIKING

ELECTRONICS

HUDSON, WI 54016

EARTH

GND

C.O. LINE

INPUT

OUT TO

PHONES

KEYLESS

C.C. INPUT

DOOR

BOX 1

DOORBOX

13VAC PWR

DOOR

BOX 2

N.O. COM N.C.

DOOR STRIKE 1

SIG GND

VIDEO 1 IN

SIG GND

VIDEO 2 IN

SIG GND

VIDEO OUT

N.O. COM N.C.

DOOR STRIKE 2

TALK BATTERY

OFF ON

LED1

LED2

LED3

1 2 3

COM N.O. N.C. - - - - AUX.

CONTACT

OUTPUT

OFF

1 2 3

Switch

E. Dip Switch Programming

Position

OFF

Description

Doorstrike Activation = 0.5 seconds (factory setting)

Doorstrike Activation = 10 seconds

Normal Mode (factory setting)

Security Code Bypass Mode

Line Concentrator Mode

Normal Operation (factory setting)

This six digit number can be used to access the programming mode. The security code has been factory set to 845464 (V-I-K-I-N-

G). It is recommended that you change the security code to a personal 6 digit number. To change the security code, access pro-

gramming (see Programming section A). Enter six digits 0-9 followed by #47. If you have forgotten your security code, follow the

steps in Programming section A, 1. Accessing the Programming Mode Locally. Note: The security code must be six digits in

length and can NOT contain a

or #.

F. Mode Descriptions

Entering these codes while in programming will switch the C-1000B into the corresponding mode.

Disable Special Modes (,0): This command disables (clears) all the special modes listed below. Enter this command before pro-

gramming the rest of the selections to be sure no unwanted modes are set.

Doorbell Mode (,1): In this mode, the ring signal from either doorbox is prevented from going through to the “LINE OUT TO

PHONES“ terminals. This is useful when a conventional door bell is connected to the auxiliary contacts. Now when someone acti-

vates a doorbox, the doorbell will chime rather than the phone ringing (see Programming section B).

Custom Ring Mode (,2): With this mode selected, the ring signal from the device ports are interrupted in a double burst pattern,

making it easier to determine if the incoming call is from a doorbox or the C.O. line. Note: Some telephones and phone systems

are not compatible with this feature.

Multiple Relay Activation Mode (,3): If selected, after a door strike command is entered, the phone is switched back to the door-

box port so additional doorstrike (relay activation) commands can be entered. This is useful when letting someone through your

gate with the first command then unlocking your front doorstrike with a second command. To return to the call on hold, enter “#”.

Paging Mode (,4): This mode is used for basic paging and/or existing installations using a C-1000B with a Viking paging ampli-

fier such as model: PA-2A. For more information, retrieve Fax Back Document 485. This mode is NOT

for use with model SLP-1.

For single line paging applications, the SLP-1 is recommended, see Installation section B and retrieve Fax Back Document 478.

Analog PABX/KSU Station Mode (,5): This mode is ideal when installing the C-1000B on a phone system that does not have a

spare trunk port but does have an unused analog station port. This mode allows any standard (POTS) telephone such as the E-10A,

E-20B, E-30 or K-1700-3 to be used in place of Doorbox 1. Only one door phone can be used in this mode. When the door phone

goes off-hook, a hot-line dialer or ringdown station will call the desired phone system extension. The phone on that extension can

then communicate with the door phone and activate doorstrikes as needed. Note: Only a single door phone may be used. Multiple

relay activation cannot be used with Viking door phone models E-10A, E-20B, E-30 or K-1700-3.

Inhibit Latching Commands Mode (,6): In some installations it is critical that the door strike or door actuator not be turned on for

long periods of time. To prevent this from happening, enter ,6 when in programming. In this mode, the toggle command (,#) and

the continuous activation command (,1) are ignored.

Auxiliary Contact Mode (,7): See Operation section 6, page 8.

CCTV Video Control Mode (,8): In this mode the C-1000B allows two CCTV video cameras to be concentrated down to one video

signal, by switching to the camera at the zone/entry point being used. When the C-1000B detects a doorbox ringing or when a door-

box is monitored, it will connect that camera’s video feed to the video output. When both doorboxes are inactive (idle), the C-1000B

can be programmed to do one of four operations (see Operation, Section C, page 8). Note: The CCTV Video Control Mode (

is disabled when using the Auxiliary Contact Mode (

7).

A. Doorbox Controller

A visitor pressing the “Call” button will cause the phones connected to the “LINE OUT TO PHONES“ terminals to ring. Simply

answer your phone to converse with the visitor. After answering the call, a single or double beep will be heard in the phone,

indicating which doorbox has called - a single beep for doorbox 1 and a double beep for doorbox 2.

1. Communicating with the Doorbox

a. Visitor Initiated Call

A doorbox may be monitored from any phone connected to the C-1000B by Touch Tone dialing a “#” followed by a Touch

Tone “1” or “2” to monitor doorbox 1 or doorbox 2 respectively. This feature is not available for pulse dialing phones. Note:

Do not attempt doorbox monitoring while a call is in progress, the call will be disconnected. Note: When monitor-

ing, the auxiliary contact will only work in the Continuous Mode (11 # 03).

b. Monitoring Doorboxes

1 2 3 4 5 6 7 8

Comentários a estes Manuais

Sem comentários

Viking C-1000B Especificações Página 7

Comentários a estes Manuais

Manuais e produtos relacionados com Sistemas de segurança - controlo de acesso Viking C-1000B