Viking C-1000B Especificações descarregar pdf (Página 5)

H. Using the C-1000B on an Analog Station Port (Analog PABX/KSU Station Mode)

Note: This mode can NOT be used with W-1000, W-2000A or W-3000 doorboxes. This application is ideal for connecting the

C-1000B to an unused analog station of your phone system. See Programming section F and Operation section A.

DOOR ENTRY / CCTV VIDEO

CONTROLLER

VIKING

MODEL C-1000B

PWR 13.8 VAC

DOOR

STRIKE 1

DOOR

STRIKE 2

DOORBOX 2

DOORBOX

PWR OUTPUT

DOORBOX 1

123456789

10 11 12 13

14 15 16 17 18 19

EARTH

GND

PHONE LINE

INPUT

LINE OUT

TO PHONES

KEYLESS CONTACT

CLOSURE INPUT

VIKING

ELECTRONICS

HUDSON, WI 54016

EARTH

GND

C.O. LINE

INPUT

OUT TO

PHONES

KEYLESS

C.C. INPUT

DOOR

BOX 1

DOORBOX

13VAC PWR

DOOR

BOX 2

N.O. COM N.C.

DOOR STRIKE 1

SIG GND

VIDEO 1 IN

SIG GND

VIDEO 2 IN

SIG GND

VIDEO OUT

N.O. COM N.C.

DOOR STRIKE 2

TALK BATTERY

OFF ON

LED1

LED2

LED3

1 2 3

COM N.O. N.C. - - - - AUX.

CONTACT

OUTPUT

13.8V AC

Adapter

included

120V AC

Standard

Analog Phone

**K-1900-5

Dialer

* K-1700-3

Phone

E-1600A

Phone

Talk Battery Switch

OFF ON

CO line or

Analog

PABX/KSU

station

E-30

Speaker Phone

Earth

Ground

(see pg 2)

E-10A or E-20B

Speaker Phones

E-10A or E-20B

Speaker Phones

5A@30V DC/

250V AC maximum

120V AC

Doorstrike/

Magnetic Lock 2

1 2 3

DIP Switches

OFF

Model

E-10A/E-20B

E-30

E-1600A

K-1700-3

K-1900-5

Fax #

210

212

215

157

317

Description

Handsfree Speaker Phone

Vandal Resistant Handsfree Speaker Phone

Emergency/Elevator Phone

Handsfree Speaker Phone with Keypad

Touch Tone Dialer

Need more information on the products shown to the right?

Call 715-386-4345 and enter the fax number below:

Note: The E-10A and E-20B

Speaker Phones may be used

without a dialer when installed

on a ring-down circuit.

Notes:

*1. The K-1700-3’s keypad can be used for extension dialing, etc., but

can NOT be used for keyless entry (see Installation and

Applications section D).

2. If “Switched” camera control is needed (for a switching video RF

modulator), connect the camera to “Video 2 In”, connect the RF

Modulator to “Video Out” and program the C-1000B with “ ,7 “

and “ 11 # 03”.

3. Once the “Analog PBX/KSU Station Mode” (,5) has been

programmed, you are not able to access the programming mode

of the C-1000B in the normal fashion. For details, see

Programming, Section A.

**4. The K-1900-5’s touch tone and flash restrictions must be disabled

(

02). See the K-1900-5 Technical Practice for complete

programming instructions, DOD# 317.

Important:

1. In this application, only a single door phone is used

and

5 must be selected when in programming.

2. Do not program the CCTV Video Control Mode (,8)

in this application (See Note 2 below). Only Auxiliary

Contact Mode (,7) can be used.

A. Accessing the Programming Mode

1. Accessing the Programming Mode Locally (Security Code Bypass Mode)

Follow Sections 1 or 2 to program a new C-1000B or any C-1000B that has not been previously programmed into the “Analog

PBX/KSU Station Mode” (,5). If the “Analog PBX/KSU Station Mode” has been programmed, follow Sections 3 or 4 to access pro-

gramming.

Note: If you are not sure how the C-1000B was previously programmed and have difficulty accessing the programming mode by

following Sections 1 or 2, follow Sections 3 or 4 in case the C-1000B is currently in the “Analog PBX/KSU Station Mode” (

5).

Step 1. Disconnect the PHONE LINE INPUT.

Step 2. Slide the TALK BATTERY switch to the ON position.

Step 3. Move DIP switch 2 from OFF to ON (see Programming section E).

Step 4. Come off-hook with a phone connected to terminals 4 & 5, LINE OUT TO PHONES.

Step 5. A double beep will indicate that you have accessed the programming mode.

Step 6. You can now Touch Tone program the features listed in section B below.

Step 7. When finished programming, hang up and move DIP switch 2 to the OFF position.

Step 8. Slide the TALK BATTERY switch back to the OFF position.

Step 9. Reconnect line to PHONE LINE INPUT.

2. Accessing the Programming Mode Remotely

Step 1. Call into the C-1000B from a Touch Tone phone.

Step 2. Answer the call using the phone (device) connected to terminals 4 & 5, LINE OUT TO PHONES.

Step 3. From either phone enter , followed by the security code (factory set to 845464, see Programming section D).

Step 4. A double beep will indicate that you have accessed the programming mode.

Step 5. You can now Touch Tone program the features listed in section B below.

Step 6. When finished, hang up both phones to exit the programming mode

Note: Programming from a cell-phone may not be suitable in areas with weak coverage.

1 2 3 4 5 6 7 8

Comentários a estes Manuais

Sem comentários

Viking C-1000B Especificações Página 5

Comentários a estes Manuais

Manuais e produtos relacionados com Sistemas de segurança - controlo de acesso Viking C-1000B