Viking Huskylock S15 Guia do Utilizador

KEEPING THE WORLD SEWING™User’s Guide

10132456788Threading the upper looper (green)1. Pass the thread from back to front through the thread guide on the thread stand (1). 2. Pull the thr

1131245678109109A9BThreading the lower looper (blue)1. Pass the thread from back to front through the thread guide on the thread stand (1).2. Pull t

12131345678456722Threading the right needle (red)1. Pass the thread from back to front through the thread guide on the thread stand (1).2. Pull the

13Changing threadThe following is an easy way to change threads:1. Cut the thread in use near the spool, behind the guides on the telescopic thread s

14Thread tension settingsSet the thread tension to suit the type of fabric and thread used. As the number on the thread tension discs increases, the

15Differential feed adjustmentThe differential feed system consists of two sets of feed teeth arranged one behind the other. Both feed teeth work ind

16Presser foot pressure adjustmentThe presser foot pressure is pre-set for sewing based on normal conditions. Adjustment might in some conditions be n

17Stitch À nger lever settingThe stitch À nger lever should be set to “S” for all standard overlock sewing. To sew rolled edge you need to retract the

18Flatlock sewingA Flatlock Stitch is made by adjusting the tension of the 2- or 3-thread overlock stitch, sewing the seam and pulling the fabric apa

19Corded overlockCorded overlock can be used to strengthen stitches when joining elastic fabrics such as knits. Cording prevents knit fabrics from str

This household sewing machine is designed to comply with IEC/EN 60335-2-28 and UL1594IMPORTANT SAFETY INSTRUCTIONSWhen using an electrical appliance,

20Machine maintenanceAn overlock requires more frequent maintenance than a conventional machine for two reasons:- A lot of lint is produced when the

21123Replacing the stationary cutter Turn off the main power switch and unplug the machine.The stationary cutter should be changed when it becomes du

22Trouble shootingProblem Solution PageFabric does not feed well - Lengthen stitch length.- Increase presser foot pressure for heavy weight fabric.- D

23Combination Needle positionStitch lengthStitch widthDifferen-tial feedStitch À nger2-thread con-verterThread tensionStitch FabricYRGB2-thread overlo

24Combination Needle positionStitch lengthStitch widthDifferen-tial feedStitch À nger2-thread con-verterThread tensionStitch FabricYRGB2-thread overlo

25Combination Needle positionStitch lengthStitch widthDifferen-tial feedStitch À nger2-thread con-verterThread tensionStitch FabricYRGB3-thread overlo

26Combination Needle positionStitch lengthStitch widthDifferen-tial feedStitch À nger2-thread con-verterThread tensionStitch FabricYRGB3-thread rolled

27Fabric / Needle / Thread tableFabric Light fabric(voile, crepe, georgette, etc.)Medium fabric(cotton, chino, wool, satin etc.)Heavy fabric(denim, je

413 17 35 - 26E • English • Inhouse • © 2010 KSIN Luxembourg II, S.ar.l. • All rights reserved • Printed in Sweden on environment friendly paperwww.hu

3Table of contentsParts of the machine ...4Accessories ...

41234568910111213141516171819724212026252322Parts of the machine1. Presser foot pressure adjustment knob2. Left needle thread tension dial (yellow)3

512345 689107Accessories1. Needle pack including three needles, size #14/90 and two needles, size #12/80. Two needles, size #14/90, are in the machin

6ASetting up the telescopic thread standExtend the telescopic thread stand to its full height, then turn until it clicks into place.Place the thread s

7AAPresser foot liftRaise the presser foot with the presser foot lift lever (A) at the back of the machine. Changing the needles Turn off the main po

8ABCDADisengage the movable upper cutterPlace the movable upper cutter in nonworking position1. Turn the hand wheel toward you until the upper cutter

92341Threading the machineA color coded diagram is located inside the front cover for quick reference.When threading the machine, thread only in the f