Viking Alarm Dialers Manual descarregar pdf (Página 4)

To program one of the seven phone numbers for each alarm input as a pager number enter: the desired 1-32 digit pager

phone number + #Q + XY (where X is the input number (1-2) and Y is the dialing order (1-7) of the seven memory locations

for this input). As with normal phone numbers, 4-second pause, Q or # can be programmed by entering Q9, QQ or Q# re-

spectively. To clear a pager number enter # + XY without any preceding digits. When dialing pagers, the K-202-DVA is

normally configured to send a certain character string when activated, that is easily recognized by the user on the pager

display. To accomplish this, the K-202-DVA is programmed with the phone number for the pager, a series of pauses (usu-

ally 8 or 12 seconds), the character string that you want to appear on the pager display ("3333333333" for example), a #

character (programmed as Q#) to "end" the call with the paging equipment, followed by #Q plus XY (where X is the input

number (1-2) and Y is the dialing order (1-7) of the seven memory locations for this input).

To program one of the seven phone numbers for each alarm input enter: the desired 1-32 digit phone number + # + XY

(where X is the input number (1 - 2) and Y the dialing order (1-7) of the seven memory locations for this input). To add a

4-second pause to the dial string (this counts as one of the 32 digits) enter Q9. To add a Q to the dial string enter QQ. To

add a # to the dial string enter Q#. To clear a number enter # + XY (where X is the input number (1 - 2) and Y is the dialing

order (1-7) of the seven memory locations for this input) without any preceding digits.

D. Programming the Phone Numbers

Description Enter Digits + Location

To enter phone numbers for each input .................................................................................. 1-32 digits + #XY*

To clear a phone number ........................................................................................................ (no digits) + #XY*

To enter pager numbers ......................................................................................................... 1-32 digits +

#QXY*

Contacts: First digit - 0 = NO, 1 = NC , 2 = enabled, 3 = disabled

Second Digit - 0 = momentary closure, 1 = continuous closure ............................

2 digits + #X9*

Repeat/Lap Counter: First two digits - message repeat counter (01-99)

Last two digits - lap counter (01-99) ...................................................

4 digits + #X0*

To program the Qualifier Timer (HHMMSS, 18 hour maximum) ............................................ 6 digits +

#XQ*

To program the Resume Operation Timer (HHMMSS, 18 hour maximum) ............................. 6 digits + #X#*

To program the Security Code ................................................................................................ 6 digits + #90

To program the Access Code .................................................................................................. 6 digits + #91

To program the Ring Delay (0-9) ............................................................................................. 1 digit + #92

To program the Ringback Limit (01-99) ...................................................................................... 2 digits + #93

To program the Forced Play Timer (01-99 seconds) (00 = clear) ........................................... 2 digits + #94

To record messages for each input (1-2) ...............................................................................

Q1 - Q2

To clear one message ............................................................................................................

Q1 - Q2 then immediately press any digit

To play message for either input .............................................................................................

Q0X*

To add a 4 second pause anywhere in the dialing string .........................................................

To add a Q anywhere in the dialing string ............................................................................... QQ

To add a # anywhere in the dialing string ................................................................................

To set to normal dialing speed ................................................................................................ ##1

To set to fast dialing speed ...................................................................................................... ##2

To program no hookswitch flash before dialing ...................................................................... ##3

To program a 500ms hookswitch flash before dialing ............................................................. ##4

To disable the PA (public address) mode ................................................................................ ##5

To enable the PA (public address) mode ................................................................................ ##6

To hang up .............................................................................................................................. ##7

To disable the Auto Resume mode ......................................................................................... ##8

To enable the Auto Resume mode ......................................................................................... ##9

To return programming to defaults .......................................................................................... ###

* X is an input number (1 or 2) and Y is the dialing order (1-7) of the seven memory locations for this input.

B. Quick Programming Features (see sections D - U for detailed descriptions)

C. Factory Default Settings

E. Programming Pager Phone Numbers

Phone Numbers Not programmed (section D)

Pager Number Not programmed (section E)

Alarm Input

Configuration

N/O (Enabled) Momentary

(section F)

Lap Counter 1 (section G)

Message Repeat

Counter

2 (section G)

Qualifier Timer 0 - disabled (section H)

Resume Timer 0 - disabled (section I)

Security Code 845464 (V-I-K-I-N-G) (section J)

Access Code 123456 (section K)

Ring Delay 1 (section L)

Ringback Limit 6 (section M)

Call Progress Detection Enabled (section N)

Messages Not recorded (section O,P)

Dialing Speed Normal (section Q)

Hookswitch Flash Before

Dialing

Disabled (section R)

PA Mode Disabled (section S)

Auto Resume Mode Disabled (section T)

1 2 3 4 5 6 7 8

Comentários a estes Manuais

Sem comentários

Viking Alarm Dialers Manual Página 4

Comentários a estes Manuais

Manuais e produtos relacionados com Sistemas de segurança - controlo de acesso Viking Alarm Dialers