Viking AES-2005 Especificações descarregar pdf (Página 5)

Black

1 8

1 12 4

Back View of the AES-2005

** Camera Pwr (+) Orange

** Camera GND (-) W/O

Yellow (Video)

3-Wire Gel-Filled Butt Connectors

included (3M Scotchlok UR2)

CAT5 Cable

To unused input on TV,

VHF modulator, whole

house video distribution

equipment, IP video

encoder (Axis M7001), etc.

120V AC

Camera GND (-)

Camera Power (+)

12V DC Adapter

(included)

(-)

(+)

W/O

Orange

*** RG59 or RG6 Shielded

Video Cable up to 1000 ft

Center conductor

stripped back 5/8"

Twisted foil and braided shield

** Up to 1000 ft

"F"

Connector

"F" to Phono Plug

Adapter

(Radio

Shack part #278-252)

- Black (GND)

+ Red (12VDC)

Crimp-on Splice

Connectors (not included)

Yellow/Red

**** Female "F" to Wire or "BNC" to Wire

Converter Cable (not included)

**** For ease of installation, a Viking Female

"F" to Wire Converter Cable can be used (Part

# 261217) or "BNC" to wire converter cable

(Part # U213510) can be used. Go to

www.vikingelectronics.com and click on

"Spare Parts" to order.

D. Wiring the AES-2005 Video Camera

1. Using RG59 for Video and CAT5 for Camera Power (Recommended)

C. Wiring Connections

Q170200Q170200

100W 0.5W100W 0.5W

J2J2

J12J12

J4J4

J10

J2J2

R12R12 R39R39

C.O. Line

or Analog

PABX/KSU

station

13.8V AC

Adapter

included

120V AC

Keyed Momentary or

Postal Lock with

Momentary Switch

Normally Closed Relay Contact

Normally Open Relay Contact

Doorstrike/Magnetic Lock #2

Relay Contact Specs:

5A @ 30VDC/250V AC

Note: Gate controllers do not

typically require power.

Normally Closed Relay Contact

Normally Open Relay Contact

Doorstrike/Magnetic Lock #1

To C-3000

Rear View

of the

AES-2005

Relay Contact Specs:

5A @ 30VDC/250V AC

Note: Gate controllers do not

typically require power.

- or -

Speaker

Volume

Microphone

Volume

AES-NET

Wiegand/CAN

Network Interface

included

OFF

Audio Detect DIP Switches

Once the AES-2005 is secured to the wall, the unit can be connected to the building wiring as described below.

Two POTs are provided to

increase or decrease speak-

er volume and microphone

sensitivity. In certain noisy

locations the speaker volume

can be increased and the

microphone sensitivity may

need to be decreased as

shown. Caution: Setting the

microphone gain too high

may cause distorted audio

and prevent the distant party

from breaking over.

Sw 1

OFF

Description

Normal audio detect sensitivity (factory setting)

Increased audio detect sensitivity for low level lines. Useful in

applications in which voice or busy signals have trouble

breaking over the speaker.

Sw 2

OFF

Step 1. Cut off the 2.1 mm plug from the end of the AC power adapter cord. The AC adapter can be located up to 100 feet away from the entry

system when using a minimum of 24 AWG wire.

Step 2. Make all connections to the AES-2005 panel before inserting the adapter into a wall outlet. The two wires from the AC adapter connect

to the two terminal block positions labeled "13.8 VAC".

Step 3. If the incoming telephone line has an RJ-11 connector, connect it to the RJ-11 jack on the control board. Two terminal positions

marked "C.O.” are also provided for a striped wire connection.

Step 4. The AES-2005 can be wired to operate a single door strike, or a door strike and an automatic door opener. The doorstrike and door

strike power supply should be wired to the terminal positions labeled "Door Strike 1". Both normally open and normally closed contacts

are available.

Step 5. If your automatic door requires a contact closure for activation, wire it to the terminal positions labeled "Door Strike 2". Both normally

open and normally closed contacts are available.

Step 6. If the installation requires a postal lock, a normally open momentary key switch can be wired to the terminal block positions labeled

“Postal Lock".

Step 7. If a C-3000 is to be used, connect a pair of wires from the AES-2005 terminal block labeled “C-3000” to the C-3000 entry phone

connection. The phone numbers for the lines wired to the C-3000 must have a “C” programmed as the first character (see

Programming). For more information, see DOD# 162 and 868.

Step 8. After all the connections are made, close and lock the hinged panel.

Step 9. The last step is to connect the A.C. power adapter to a wall outlet. When power is connected to the system, the front display should

show "Welcome!"

Note: The door strike and door opener can be tested using the default keyless entry code programmed in the panel. Dial “#” plus “00864” on the

AES-2005 keypad.

1 2 3 4 5 6 7 8 9 10 11

Comentários a estes Manuais

Sem comentários

Viking AES-2005 Especificações Página 5

Comentários a estes Manuais

Manuais e produtos relacionados com Sistemas de segurança - controlo de acesso Viking AES-2005