2. Accessing the Programming Mode Locally (Security Code Bypass Mode)
Step 1. Move DIP switch 2 from OFF to ON (Security Code Bypass Mode, see DIP Switch Programming section D).
Step 2. Come off-hook with any house phone connected to terminals 4 & 5, LINE OUT TO PHONES.
Step 3. A double beep will indicate that you have accessed the programming mode.
Step 4. You can now Touch Tone program the features listed in section B below.
Step 5. When finished programming, hang up and move DIP switch 2 to the OFF position.
Step 1. Connect the power, required entry phones and doorstrike
outputs (if required) as shown in section A.
Step 2. Connect an analog phone or unused phone system (PABX/
KSU) line /trunk port to terminals 4 & 5, “LINE OUT TO
PHONES” on the C-2000A.
Step 3. Access programming as shown in Programming section
A, 2. below. Enter
5, two beeps should be heard.
Step 4. Enter additional desired programming, then hang-up the
phone and place DIP switch 2 back to the OFF position.
The C-2000A can also be used without a C.O. line. This is
ideal for connecting the C-2000A to an unused trunk/line input
of your phone system or connecting to phones used only for
doorbox communication.
VIKING
©
MODEL C-2000A
VIKING
ELECTRONICS
HUDSON, WI 54016
ADVANCED DOOR/GATE AND
ENTRY PHONE CONTROLLER
1 2 3 4 5
67
8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30
PWR 13.8 VAC
EARTH GND
ENTRY PHONE 1
DOOR STRIKE 1
ENTRY PHONE 2
DOOR STRIKE 2
ENTRY PHONE 3
DOOR STRIKE 3
ENTRY PHONE 4
DOOR STRIKE 4
DOORBELL SWITCH /
AUX. INPUT
AUX. CONTACT
OUTPUT
PHONE LINE
INPUT
LINE OUT
TO PHONES
or
Standard
Analog
Phones
Unused Line /
Trunk Input on
Phone System
(PABX/KSU)
13.8V AC
Adapter
(included)
120V AC
VIKING
©
MODEL C-2000A
VIKING
ELECTRONICS
HUDSON, WI 54016
ADVANCED DOOR/GATE AND
ENTRY PHONE CONTROLLER
1 2 3 4 5
67
8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30
PWR 13.8 VAC
EARTH GND
ENTRY PHONE 1
DOOR STRIKE 1
ENTRY PHONE 2
DOOR STRIKE 2
ENTRY PHONE 3
DOOR STRIKE 3
ENTRY PHONE 4
DOOR STRIKE 4
DOORBELL SWITCH /
AUX. INPUT
AUX. CONTACT
OUTPUT
PHONE LINE
INPUT
LINE OUT
TO PHONES
STAND-ALONE
DOOR CONTROLLER
ENTRY SYSTEM
VIKING
PROGRAM
PHONE
GANG
PROG
COMM
ELECTRONICS
HUDSON, WI 54016
VIKING
©
MODEL ES-1
POWER 12 VDC
BLK
RED
GRN
WHT
ENTRY POINT
WIEGAND
DEVICE
LOG
BUS
Viking HID-1
Proximity Card
Reader (not included)
Viking HID-2
Keypad
(not included)
and/or
12V DC
Adapter
(included)
120V AC
13.8V AC
Adapter
(included)
120V AC
(Power typically
not required for
gate controllers)
Doorstrike/
Magnetic Lock
5A@30VDC/
250VAC
maximum
D. Using the C-2000A with a Proximity Card Reader or a Separate Keyless Entry Keypad
C. Using a C-2000A without a C.O. Line
Step 1. Program the ES-1 “Relay Activation Time” to match the “Doorstrike Activation Time” on the C-2000A.
Step 2. Connect the ES-1 relay output in parallel with the doorstrike output contacts on the C-2000A.
Step 3. Connect the entry phones and doorstrike outputs (if required) as shown in section A.
?
Need More Information on the HID-1?
Call (715) 386-4345 and select 197.
?
Need More Information on the ES-1?
Call (715) 386-4345 and select 193.
?
Need More Information on the HID-2?
Call (715) 386-4345 and select 199.
P
P
r
r
o
o
g
g
r
r
a
a
m
m
m
m
i
i
n
n
g
g
A. Accessing Programming
1. Accessing the Programming Mode with a Security Code
Step 1. Come off-hook with any house phone (device) connected to terminals 4 & 5, LINE OUT TO PHONES.
Step 2. Enter # followed by the 6-digit security code (factory set to 845464, V-I-K-I-N-G, see Programming section C).
Step 3. A double beep will indicate that you have accessed the programming mode.
Step 4. You can now Touch Tone program the features listed in section B below.
Step 5. When finished programming, hang up.
4
Note: This mode is useful for programming the C-2000A without a telephone line connected.
(8 páginas)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais